Tobacco Pine Flooring

Untitled

Tobacco Pine Flooring
RECLAIMED FLOORING 100% BARNS USED FOR CURING TOBACCO
Tobacco Pine Flooring. … In 1612 the settlers of the first American colony in Jamestown, grew tobacco as a cash crop. In the 21st century they are fast disappearing barns used for curing tobacco. …

Tobacco barns used  for the curing of tobacco in the early 1900’s, they our fast disappearing from the American landscape. Reclaimed from old barns, factories and warehouses wide planks milled into exceptional wood flooring. Low cost start at: $4.25 SQ. FT. …

Tobacco Barns

Wikipedia

The Terminology ” Tobacco Barn” used for strikly tobacco curing some have large tobacco barn wood floors.Solid by a few companys dismantled barns for sale or old barns for sale to be moved and reclaimed wood for sale near me much tobacco wood has been soild that way. Some tobacco wood used primerly asreclaimed pine flooring for sale some stain reclaimed hard wood floors. Barn barns have used oak flooring or reclaimed white oak beams and salvaged hardwood flooring many people use old wood barns for sale or disassembled barns for sale some have old barns for free and old barns for sale classified ads.

We prefer not to apply any finishes to our Reclaimed Wood Floors because each customer needs or different and the look they are wanting to achieve.  Tobacco Pine there were many barns made using Hemlock. We ship freight, palletized (1,000 sq.ft. per skid ) and shrink wrapped. Phone for more info: 1-301-334 ( 3189 ).
Recommended Nail-Down Tools:
1. Pneumatic 18-gauge tongue-and-groove flooring nailer
2. Use 1-1⁄2″ to 2″ long, 18-20 gauge cleats for flooring
3. Underlayment (see Moisture Barrier Requirements)
4. Tapping block (trimmed piece of flooring)
5. Wood or plastic spacers (1/2″)
6. Flat bar or pull bar
The selection and use of any nailer is at the discretion and responsibility of the installer/ homeowner. Choose a nailer model that is specifically designed for tongue and groove applications. We recommend a Pneumatic 18 Gauge Flooring Nailer (such as Powernail 50p Flex or similar). It is the installer’s responsibility to determine the correct pressure for their stapler/nailer, and to ensure that the fastener is properly seated. Dimpling of the flooring face or edge is not a manufacturing defect.
Nail Down Installation Steps:
1. When nailing, the flooring should be always laid perpendicular to the floor joist.
2. Allow a 1/2″ space for expansion around the perimeter of the room and all vertical objects using spacers.
3. Dry lay (do not nail) a couple rows before starting installation to confirm your layout plan.
4. Test the air pressure and angle of your pneumatic nailer with a sample plank to check for correct air pressure before installation. If you note any surface damage (face dimpling), tongue damage (splitting), etc., adjust the air pressure/angle accordingly. Test until dimpling no longer occurs.
5. Begin installation next to an outside wall. This is the best reference for establishing a straight working line.
6. With groove facing the wall, lay the first starter row in place by blind nailing or gluing to avoid unsightly nail marks.
7. Connect short side of second plank together with the mating side of the first plank.
8. Cut last plank and complete row. Use the remaining plank to start the second row.
9. Be sure to offset the end joints of consecutive rows by a minimum of six (6) inches for best appearance.
10. Continue the second starter row by connecting the short edges first and use a pull bar to tap the long edges together.
11. After the first two rows are secured, install the remaining rows by nailing directly above the tongue at a 45 degree angle.
12. Carefully monitor nailer pressure to ensure that the nail head enters the tongue only as deeply as required to allow the adjacent plank to fit properly. Ensure that the nail head rests cleanly in the “nail pocket”.
13. Recommended nail spacing is 8 to 10 inches along the length of each board.
14. Avoid nailing closer than 4 inches from the end of the plank.
15. As with the other rows, connect the short edges first and use a pull bar to tap the long edges together.
16. Regularly check your working lines to be sure the floor is still aligned.
17. The last row may require rip cutting the planks to size.
18. The last two rows will need to be secured in the same manner as the first two rows.
After Installation:
The newly installed floor is complete and can be walked on immediately.
Use wood filler, a finish touch-up kit or putty to correct minor flooring damage that occurs during installation.

Precisely what you want!

Call or Fax us for information & quotes at:
P: 
1-240-321-1205

Email us at: robertu@coloniallumber.com

Tobacco Pine Flooring